顯示文章

這裡允許您檢視這個會員的所有文章。請注意, 您只能看見您有權限閱讀的文章。


文章 - 山姆小弟

頁: [1]
1
肉腳版 / rtorrent + ntorrent on centos
« 於: 2009-08-20 11:53 »
小弟最近開始用rtorrent 在網路上發現ntorrent可以遠端監視rtorrent
照網路上的安裝方法要先安裝xmlrpc-c,而安裝xmlrpc-c需安裝
make
pkg-config
sigc++-2.0-dev
libncurses-dev
libcurl-openssl-dev

make,pkg-config我已經裝了,剩下的要去哪下載呢?謝謝~

PS-我使用CentOS 5.3

2
肉腳版 / 電腦關機後Switch還會送封包嗎?
« 於: 2009-08-18 16:57 »
最近研究如何Wake on lan

電腦關機後switch偵測不到

那發送Magic packer還會送到嗎?

使用ADSL當Switch,arp會保存多久?

會不會時間太長arp更新就無法喚醒關機電腦?

謝謝回答~

3
感謝你的回答...
這要用DNAT來做才可以...

4
雜七雜八 / 你心目中理想的17吋夢幻LCD
« 於: 2004-04-25 02:32 »
我使用的也是三隻小鳥的VE175...
之前在當兵的時候我們的辦公室就是使用這種的...
但是使用不到一年就有些小毛病....
螢幕有時候會花掉....
要關掉重新打開才會恢復...
可能是控制面板快掛了吧...
還好他有提供三年保固....
畫質與亮度是不錯啦...
想想實在沒啥可挑剔的...

5
可以呀 你有試過了嗎 先試試看吧 失敗在上來問囉

6
Network 討論版 / 中華電信
« 於: 2004-04-21 03:56 »
中華電信是在壟斷網路... :(

他不想失去專線用戶這些大金主

所以我們這些付不起專線費用的小老百姓

只能看著其他國家的費率流口水... :cry:

有在玩WinMX應該知道日本他們的上傳速度

交換檔案時還會因為上傳太慢被踢掉... :evil:

7
問網管吧~ :lol:
實體層好像沒有可用的軟體... :roll:

8
請善用google論壇搜尋tw.bbs.comp.linux 你的答案就在上面

與其問別人不如自己找答案比較快

大部分的問題都有人問過 也有人回答

9
Linux 討論版 / 不給dhcp
« 於: 2004-04-11 15:11 »
如果他只是使用dhcpd取得ip 可在/etc/dhcpd.conf 設定MAC對應IP
host pc-2 { hardware ethernet 00:0E:A6:4A:35:50; fixed-address 192.168.0.2; }
如果他手動設定ip就蠻麻煩的 你要知道你網域內所有電腦的MAC
將之輸入至/etc/ethers
192.168.0.2 00:00:00:00:00:00 <=上面給他分配到ip的MAC設成0
192.168.0.3 00:50:FC:3F:9F:D1
192.168.0.4 00:90:CC:27:25:F3
192.168.0.5 00:40:F4:40:00:3A
192.168.0.6 00:90:CC:27:25:F6
192.168.0.7 00:40:F4:59:D1:5D
192.168.0.8 00:0E:A6:4A:35:50
其餘未分配到ip(9~255)的mac也都設成0然後下達arp -f

10
肉腳版 / [問題]硬碟有壞的blocks...
« 於: 2004-04-07 04:04 »
因為硬碟一直出現下列訊息 我查到有可能是壞軌造成

hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }

badblocks -sv /dev/hda2
Checking for bad blocks in read-only mode
From block 0 to 25599577
Checking for bad blocks (read-only test): 255995766/ 25599577
done
Pass completed, 1 bad blocks found.

fsck.ext3 -c /dev/hda2 <=無法修復壞軌並且沒有找到壞軌

去google搜尋tw.bbs.comp.linux找關於壞軌的資料
但是都使用fsck來掃描硬碟可是都掃不出來那壞的blocks...

11
肉腳版 / [問題]block size 如何查....
« 於: 2004-04-06 11:43 »
我上google 查到要用 tune2fs...
是這樣查嗎 tune2fs -i...?
可不可以指導一下... :lol:

12
日韓港台xDSL月費比較表

想請問各位網管大大

台灣的網路費用是不是真的不合理呢

中華電信四月起開放撥接速率 1.5M/64K 以上配發固定IP

為什麼死都不開放"最後一哩"...

13
我同學有顆160GB的硬碟,在他的電腦格式化了八個小時才完成了百分之七,想說如果要這麼久就用LINUX伺服器來做比較沒有影響,但是搜尋討論區並沒有相關的說明,所以就發表一篇看有沒有人知道...感謝啦  :lol:

14
iptables -t nat -A POSTROUTING -o ppp0 -s 192.168.0.0/24 -j MASQUERADE

小弟使用上列的設定 但是eMule總是獲得LowID要如何設定才能獲得HighID呢?

他的說明指出不能使用封包偽裝(MASQUERADE) 我要如何讓內網直接連線呢?

15
太感激了 真是謝謝這位大大的回答 ^^

16
這是他的INSTALL.unix.txt

install Python, version 2.0 or later - http://python.org/

install wxPython - http://wxpython.org/

(under debian, you can currently get the above using
apt-get install libwxgtk2.2-python
from testing and use python 2.1)

untar and put a line in /etc/mailcap which is similar to the
following, only replace the path to
/usr/bin/btdownloadgui.py with the one it's actually in.

application/x-bittorrent; /usr/bin/btdownloadgui.py %s; test=test -n "$DISPLAY"

You may have to restart your web browser for it to start
using BitTorrent.

If you're using a web browser which doesn't respect
/etc/mailcap you can go into the mimetype configuration for
your web browser and manually associate application/x-bittorrent
with btdownloadgui.py (with the appropriate path, of course.)

這是他的Readme

BitTorrent is a tool for distributing files. It's extremely
easy to use - downloads are started by clicking on hyperlinks.
Whenever more than one person is downloading at once
they send pieces of the file(s) to each other, thus relieving
the central server's bandwidth burden. Even with many
simultaneous downloads, the upload burden on the central server
remains quite small, since each new downloader introduces new
upload capacity.

Windows web browser support is added by running an installer.
A prebuilt one is available, but instructions for building it
yourself are in BUILD.windows.txt

Instructions for Unix installation are in INSTALL.unix.txt

To start hosting -

1) start running a tracker

First, you need a tracker. If you're on a dynamic IP or otherwise
unreliable connection, you should find someone else's tracker and
use that. Otherwise, follow the rest of this step.

Trackers refer downloaders to each other. The load on the tracker
is very small, so you only need one for all your files.

To run a tracker, execute the command bttrack.py Here is an example -

./bttrack.py --port 6969 --dfile dstate

--dfile is where persistent information is kept on the tracker across
invocations. It makes everything start working again immediately if
you restart the tracker. A new one will be created if it doesn't exist
already.

The tracker must be on a net-addressible box, and you must know the
ip number or dns name of it.

The tracker outputs web logs to standard out. You can get information
about the files it's currently serving by getting its index page.

2) create a metainfo file using btmakemetafile.py

To generate a metainfo file, run the publish btmakemetafile and give
it the file you want metainfo for and the url of the tracker

./btmakemetafile.py myfile.ext http://my.tracker:6969/announce

This will generate a file called myfile.ext.torrent

Make sure to include the port number in the tracker url if it isn't 80.

This command may take a while to scan over the whole file hashing it.

The /announce path is special and hard-coded into the tracker.
Make sure to give the domain or ip your tracker is on instead of
my.tracker.

You can use either a dns name or an IP address in the tracker url.

3) associate .torrent with application/x-bittorrent on your web server

The way you do this is dependent on the particular web server you're using.

You must have a web server which can serve ordinary static files and is
addressable from the internet at large.

4) put the newly made .torrent file on your web server

Note that the file name you choose on the server must end in .torrent, so
it gets associated with the right mimetype.

5) put up a static page which links to the location you uploaded to in step 4

The file you uploaded in step 4 is linked to using an ordinary url.

6) start a downloader as a resume on the complete file

You have to run a downloader which already has the complete file,
so new downloaders have a place to get it from. Here's an example -

./btdownloadheadless.py --url http://my.server/myfile.torrent --saveas myfile.ext

Make sure the saveas argument points to the already complete file.

If you're running the complete downloader on the same machine or LAN as
the tracker, give a --ip parameter to the complete downloader. The --ip
parameter can be either an IP address or DNS name.

BitTorrent defaults to port 6881. If it can't use 6881, (probably because
another download is happening) it tries 6882, then 6883, etc. It gives up
after 6889.

7) you're done!

Now you just have to get people downloading! Refer them to the page you
created in step 5.

BitTorrent can also publish whole directories - simply point
btmakemetafile.py at the directory with files in it, they'll be published
as one unit. All files in subdirectories will be included, although files
and directories named 'CVS' and 'core' are ignored.

If you have any questions, try the web site or mailing list -

http://bitconjurer.org/BitTorrent/

http://groups.yahoo.com/group/BitTorrent

You can also often find me, Bram, in #bittorrent of irc.freenode.net

我想學LINUX英文一定要加強吧 還是使用翻譯軟體呢 可以推薦好用的翻譯軟體嗎 @@

17
我是下載這個網站的http://bitconjurer.org/BitTorrent/BitTorrent-3.3.tar.gz

我已經把Python裝上去了wxPython也要裝嗎...?

我只跑文字模式的....

18
GIGA是要我把PROXY設成giga-mirror1.ix4g.com這個代理伺服器
但是還是沒辦法下載ㄝ 有沒有使用Hinet的大大 可以下載GIGA呢

19


請問 169.254.0.0 這個 eth1 是哪來的呢

20
該死的 Hinet ...
可是我同學用 Seednet 就可以ㄝ
Hinet 怎麼這麼小氣呀
難怪我朋友死都不申請 Hinet ...

21
各位大大是否有解決方案呢
小弟只要連結到 home.gigigaga.com 的網頁
就會顯示說是 hinet 限制無法下載
難道這兩家就水火不容無法下載

22
WIN2K可以用中文建立帳號,Linux應該也可以吧?該如何建立中文帳號呢?謝謝

23
各位大大 小弟在家連接區域網路給五台電腦上網 想讓每台都可使用印表機 但對市面上的印表機性能不是很了解 也不確定是否有支援Linux 想請使用Linux的同好 推薦您覺得使用上很滿意的印表機 謝謝  :D

24
請問我使用Nero燒錄軟體時,只有用Administrator才能抓到燒錄機,Power User不能,還有裝完Office2000用Power User權限不能讀取註冊資訊,請問要更改哪個設定,謝謝。  :D

頁: [1]