作者 主題: mdk9 linux network config problem?  (閱讀 3510 次)

0 會員 與 1 訪客 正在閱讀本文。

我是肉腳

  • 訪客
mdk9 linux network config problem?
« 於: 2003-05-22 20:49 »
之前我灌redhat linux 都沒有問題耶
#dmesg

les configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 121k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xd483b000, IRQ 20
usb-ohci.c: usb-00:02.2, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xd483d000, IRQ 23
usb-ohci.c: usb-00:02.3, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal journal
Adding Swap: 530104k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: LITE-ON   Model: LTR-48246S        Rev: SS0A
  Type:   CD-ROM                             ANSI SCSI revision: 02
hdd: ATAPI 52X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
8139too Fast Ethernet driver 0.9.25    <-------有抓到耶!
eth0: RealTek RTL8139 Fast Ethernet at 0xd485f000, 00:50:fc:75:1f:fc, IRQ 16
eth0:  Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: Each connection entry needs 116 bytes at least
IPVS: ipvs loaded.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
intel8x0: clocking to 48000
inserting floppy driver for 2.4.19-16mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
sr0: scsi3-mmc drive: 138x/48x writer cd/rw xa/form2 cdda tray
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00002000. (queue head)
eth0:  Tx descriptor 1 is 00002000.
eth0:  Tx descriptor 2 is 00002000.
eth0:  Tx descriptor 3 is 00002000.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00002000. (queue head)
eth0:  Tx descriptor 1 is 00002000.
eth0:  Tx descriptor 2 is 00002000.
eth0:  Tx descriptor 3 is 00002000.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.

最後這兩個我不太懂他的意思 :oops:
(我是用學校的區域網路上的,netman跟鳥哥的網路設定或偵錯我都實作一遍了說)
 :oops:

netman

  • 管理員
  • 俺是博士!
  • *****
  • 文章數: 17479
    • 檢視個人資料
    • http://www.study-area.org
mdk9 linux network config problem?
« 回覆 #1 於: 2003-05-22 23:36 »
嗯?換片卡或換個牌子(如 intel 或 3com)的來看看?

godpk

  • 懷疑的國中生
  • **
  • 文章數: 70
    • 檢視個人資料
mdk9 linux network config problem?
« 回覆 #2 於: 2003-05-22 23:57 »
你用的是 螃蟹卡?

我是肉腳

  • 訪客
mdk9 linux network config problem?
« 回覆 #3 於: 2003-05-23 01:09 »
是的!
8139too  :o

  • 實習板主
  • 活潑的大學生
  • ***
  • 文章數: 270
    • 檢視個人資料
mdk9 linux network config problem?
« 回覆 #4 於: 2003-05-24 15:52 »
也許開機無法使用網卡是因為之前給的安裝參數不正確而已

在console下用drakconnect指令
重新設定一次網路連線。

或者在圖形介面下設定-Mandrake Control Center再設定一次